Sump Oil Filter Strainer Plate Gasket. Fits: All 650's 1970-84

Gear Train Cover Gasket - Gasket for cover that is removed when installing the starter block-off plug. (This gasket is located below front sprocket and under left hand engine case). OEM # 306-15452-00. Fits: 1972-84 650's

At Base of 6 Bolt Cam Chain Tensioner Case Gasket. (Can use for 4 bolt type). OEM Ref.# 306-12213-01. Fits: 1970-84 650's

Gasket - Engine Breather Cover - OEM Ref.# 256-11169-01. Fits: All 650's 1970-84

Rear of Advance or Breaker Housing Gasket. 2 used on each engine. OEM Ref.# 256-11146-00. Fits: All 650's 1970-84

Right Hand Crank Case Cover (Clutch) Gasket. OEM Ref.# 256-15451-00. Fits: 1970-84 650's

Intake Spiggot Gasket (Carb Holder Rubber) (Pk/2), OEM Ref.# 256-13556-01. Fits: Between XS650 Manifolds (Carb Spacers) and cylinder head and between the XS manifolds and the carb holders for the PWK 32. Fits: 1970-84 650's Keihin Flatslide PWK 32mm XS Performance Carb Set for XS650. Note: 2 sets required.

Oil Dipstick Gasket. OEM Ref.# 256-15364-00. Fits: All 650's 1970-84

Cam Chain Adjuster Cover O-Ring (Nut) - OEM Ref.# 93210-21190 (Late type). Fits: Tensioner type D & E on XS650's

Early Cam Chain Adjuster Cover O-Ring. (Cover with 22mm Hex). Fits: Type C tensioner as used on TX650A (1974), XS650B (1975)

Left Hand Crankcase Cover Gasket. OEM Ref.# 306-15461-00. Fits: 1972-84 650's.

Top End Copper Sealing Washer Kit - 9 pc. Kit Contains: 1pc. # 90430-14043 ( @ Oil feed tube base at crankcase), 4 pc. # 90430-10027 ( @ Oil feed tube - Top of head at bolts), 2 pc. # 90430-11033 (@ Rear of cam chain guide support nuts to cylinder front), 2 pc. # 90430-06014 @ (Cam chain guide fastening bolts at front of cylinder). Fits: All 650's

Bottom End Copper Sealing Washer Kit - 13 pc. Kit Contains: 6pc.of # 90430-08143-00 ( @ Crankcase Bottom - Nut washers), 2 pc.of #90430-06014 ( @ Oil filter cover screws in clutch case), 3 pc. 90430-06014 ( @ 3 Clutch case upper front screws), 1 pc. of # 90430-06014 ( @ Tach drive retaining bolt), 1pc. 37R-82543-00/90430-11034 ( @ Neutral switch base). Fits: All 650's

Copper Gasket - Cam Chain Adjuster Screw / Lock Nut. OEM Ref.# 90430-18130. Fits: E Type tensioner as used on XS650 2F,G/SG/H/SH/SJ/SK (1980-84)

Cam Chain Tensioner Rod to Spring Damper. OEM Ref.# 2H0-12232-00. Original part on XS650H/SH/SJ/SK (1981-84) and will replace OEM # 341-12232-02 as used on (1974-80) models.