Clutch pushrod shaft Bushing Replaces original bushing inside of pushrod housing (transmission shaft) and brings clearances back to original. When stock clearances are too large the pushrod moves to the side and increases tearing stress on the pushrod seal.

Clutch Pushrod Oil Seal Made in Japan OEM Ref.# 93102-08094/08118 (SD - 8-25-6) Ars

Cable Adjuster - 8 x 23mm. - Gold Anodized Fits: All 650 Clutch Cables

Brake Lever - (Chrome plated version of 08-0111) Fits: XS650 SE/F/2F/SF/SG/SH/SK/SL 1978-84 and XS650S J/K Heritage Specials. OEM Ref.#'s 2H7-83922-00, 2H7-83922-20, 2J2-83922-20, 4L0-83922-00 Also Fits our 08-0255/0265 Master Cylinders.

Lever Bracket - Clutch Side, Late Model 650 Yamaha type with Safe-T switch hole and threaded mirror hole. Includes adjuster and lever bolt. OEM Ref.# 4KO/3Y6-82911-00 If you require a lever for this bracket, please purchase our 08-0028 lever.

Lever Bracket - Clutch Side, Has threaded mirror hole and includes adjuster and lever bolt. (No safe T switch hole). OEM Ref.# 498/341-82911 Fits: Most 1974-80 models If you require a lever for this bracket, please purchase our 08-0028 lever.

2 pc. Lever Bracket - Clutch side - With Safe-T switch hole. Much stronger and can be changed without removing grip. Fits: Most 1981-84 650's If you require a lever for this bracket, please purchase our 08-0028 lever.

2 pc. Lever Bracket - Clutch side - No Safe-T switch hole. Fits: most 1972-84 650's If you require a lever for this bracket, please purchase our 08-0028 lever.

Clutch Adjuster Cover - Chrome - Covers adjuster screw in LH crankcase cover. Fits: 1971-84 650's

Clutch Friction Plate Fit: All 650's 1970-84 - Sold Each - Order number of pieces required. 1980-84 models - use 6pc. 1974-79 models - use 7pc.. 1970-73 model clutch friction plates are No longer available but these later types can replace the originals! (6 friction and 5 steel drive plates were originally used). To use these late type friction plates remove the old clutch plate separator O-Rings (discard), and add 1 additional steel drive plate and replace all 6 old type thick friction plates with 7pc. of this new type friction plate.

Clutch Spring Screw Set - 12pc. - 6 Socket Head Bolts with Matching Sleeves. Fits: 1970-84 Clutch Hub

Needle Bearing with Thrust Washer for Rear of Inner Clutch Hub. Fits: All 650's If your clutch does not seem to release properly or if you have difficulty finding neutral when the engine is hot a worn bearing may be the reason. Our high quality multi-needle bearing assembly is a superior replacement for the original. Note: Bearing Part #39-6505 (OEM Ref.#93341-23504) consists of - 1. the circular bearing race and 2. one thin matching washer. Parts books and manuals show this as 1 part only (not 2 pc). The Clutch must be assembled in Sequence shown above - Bearing with its matching thin washer and then the thick clutch washer (thrust plate).

High Performance Clutch Springs - Set of 6 - Replaces/upgrades sagged original stock springs.

Steel Clutch Drive Plate Fit: All 650's 1970-84 - Sold Each - Order number of pieces required. 1980-84 models - use 5pc. 1974-79 models - use 6 pc. 1970-73 (use 5pc. OR 6pc. if the clutch is upgraded to late type friction plates. See friction plate listings for conversion info). Oem Ref.# 341-16325-01

Clutch Pushrod Bearing, 2 used in each 76-84 engine, (only 1 pc. required if long early 70-75 type clutch pushrod is used). Fits: 1970-84 XS/TX650's.