Gear Shift Lever with rubber. Chrome plated steel. Fits: 1970-84 650's

Extended Bigfoot Gear Shift Lever - Do you have feet Larger than the guy that designed the gear lever on your XS? This extended gear lever for the XS650 will fit better and also improves shifting! Includes rubber. Fits: 1970-84 650's

Kickstarter Spring Fits: All 650's 1970-84

Lower Engine Case Screw Set. - 18pc. Fits: Lower right hand & left hand engine cases on all 650's.

Engine Top Fastener Set - 55pc. 55pc. Kit Contains: 3 Hole Tappet Cover chromed Crown Nuts (12pc.) with matching chrome Washers (12pc.) + Cylinder Head chrome Crown Nut (8pc.) + chrome rocker shaft End Plug (4pc.) + Point/Cam Cover chrome Screws (4pc.) + Exhaust Stud chrome Crown Nuts (4pc.) with matching Stainless Lock Washers (4pc.) + 2pc. Chrome Oil tube banjo bolts, + 2pc. Chromed Cylinder front/Cam chain guide bar Nuts, + 2pc. chromed cam chain guide bar bolts. Fits: 1970-71 650's

Cylinder Head Hardware Set Fits: 1972-84 XS/TX 650's

Polished Chrome Shock Crown Nut - Short Type. 17mm hex x 10mm 1.25pitch x 16mm Long. Fits: All Footrest mount bars 70-84 + Fender mount thru point on 76-78's.

Chrome Thick Washer - 10mm x 27mm x 4.5mm. Fits: All Footrest mount bars on 1970-84 650's and shock absorber top mount stud on 1974-79 650's.

Advance/Breaker Housing Screw & Washer Set (6pc. Set). Includes: 3 countersunk flat-head type screws and 3 matching starlock washers. 2 sets required to do both engine housings on each engine. Fits: All 650's 1970-84

Oil Delivery Tube Banjo Bolt Pk/2 - Attaches Delivery Pipe to Cylinder Head - Chrome Plated. Fits: All 1970-84 650's

Decompressor Cable (Grey) - OEM # 306-26371-00-00 - Made in Japan. Fits: XS2 (1972), TX650 (1973)

Bolt - Special Bolt that Holds the Tach Drive into the Clutch (RH Engine) Case. Fits: All 650's 1970-84

Endless One Piece Cam Chain - Daido 219FTss x 106 - Pitch .3061" (7.774mm). Fits: (36 tooth cam) The latest high strength cam chain from D.I.D. for late XS650's. High Quality Made in Japan. Note: As this is an endless chain you need to buy link #01-8802 if you plan on breaking the chain to install. Installation Note: Cam Chain IS absolutely correct original brand/size/length/type Original install will be Very tight as chain is pressure injected with grease at factory and head gasket is not yet compressed. Install with tensioner assembly out and it may be necessary to pry chain over last half tooth of cam sprocket to get the chain in place so joiner link can be installed. Chain will loosen once head is torqued and engine is run a short time.

Cam Chain - Tsubaki BF05T x 102 with Rivet Link. Pitch .315" (8.0mm). Made in Japan. Fits: XS1/XS1B/XS2/TX650 1970-73 (34 tooth cam). NOTE: Link pitch differs from chains used on later 650's. For 70-73 650's Only! Installation Note: Cam Chain IS absolutely correct original brand/size/length/type Original install will be Very tight as chain is pressure injected with grease at factory and head gasket is not yet compressed. Install with tensioner assembly out and it may be necessary to pry chain over last half tooth of cam sprocket to get the chain in place so joiner link can be installed. Chain will loosen once head is torqued and engine is run a short time.

Engine Oil Seal - Starter motor to Crankcase OEM Seal #93102-34095 Ars SD34-46-10.5