Gas Tank Mount Rubber - Front - Each

Gas Tank Mount Rubber - Rear OEM Ref# 256-24181-01

54mm. XS Performance Pod Filter - Tapered Oval Style with Chrome End Cap. Pod is an improved replica (Dyno & flow bench developed) of the most popular brand on the market. Features molded in internal stack, no step rubber mount flange and Chrome end cap. Filter is supplied dry but washable filtration material may be oiled for improved dust filtration. Filter body is 71mm. (2.8") deep x 74mm. (2.91") wide x 101mm. (4") high (at base). Fits: 1980-84 stock Mikuni BS34 CV Carbs + some Mikuni TM aftermarket carbs. + Fits Keihin Flatslide PWK 32mm. XS Performance Carb Set for XS650 Note: Each kit requires 2 filters.

52mm. XS Performance Pod Filter. Pod fits to velocity stack on Dellorto PHF36 carbs (this combination has been shown on Dyno tests to give the most power). Pod filter is a New XS Performance item and is an improved replica (Dyno developed) of the most popular brand on the market. Chrome end cap, internal moulded stack and no step rubber mount. Pod filter is supplied dry but cotton gauze filtration material may be oiled for improved dust filtration. Fits: 1970-79 stock Mikuni BS38 CV Carbs + some Mikuni TM aftermarket carbs. + Fits our XS#48-7000 Carb Kit.

Air Filter - OEM Ref.# 306-14451 - Made in Japan. Fits: XS2/TX650 1972-73 2 used per bike

Air Filter - OEM Ref.# 533-14451-00 - Made in Japan. Fits: XS650C/D/E 1976-78 + XS650F (1979) Plus: The bikes below use either this filter or our filter #15-0655. Check which type you require before purchasing for the models below. Yamaha: XS650SE (1978), XS650SF (1979), XS650SG (1980) Sold Each, Order Quantity Required

Air Filter - OEM Ref.# 3G1-14451 - Made in Japan. Fits: Yamaha XS650G (1980), XS650H (1981), XS650SH (1981), XS650SJ (1982), XS650SK (1983) Plus: The bikes below use either this filter or our filter #15-0653. Check which type you require before purchasing for the models below. Yamaha: XS650SE (1978), XS650SF (1979), XS650SG (1980) Sold Each, Order Quantity Required

Rubber Joint - Carb to Air Filter Box - 1Pc. of Air Box Rubber Joint & 2pc. of Tension Spring. Fits: 1970-84 XS/TX 650's - Carb to air box - right or left side. Each bike requires 2 sets.

Rubber Joint (Between Air Filter Boxes) and Spring. Fits: Stock Air boxes used on 1974-84 650's.

Engine Breather Hose & Spring - Black Vent Hose & 10" Spring

Petcock Rebuild Kit - These Petcocks Have a 3 Screw Rear Cover Plate. Kit Contains: 1pc. Valve Rubber, 1pc. Wave Washer, 1pc. Tap to tank O-Ring, 2pc. Tank bolt Washer, 1pc. Drain screw Gasket, 1 pc. Rear cover Gasket (3 Screw type). Fits: TX650/A 1973-74, XS650B/C/D 1975-77

Petcock Mount O-Ring - (Tap to Tank O-Ring) Fits: Petcocks on 1970-77 650's

Sealing Washers for Tap to Tank Mount Screws. Fits: Under Mount Screws on 1970-84 650's

Petcock - Non Vacuum Type to Replace 1978-84 Vacuum Type Petcocks. All 1978-84 North American market 650's have original petcocks operated by Vacuum from a line to the intake (on carb holder). 1978-79 models have 2 and 1980-84 models have 1 petcock. Vacuum petcocks are chronic leakers and are all getting to the point of being non-repairable. Our petcock is the Early type 650 manual petcock with a wider flange cast on it so it will fit in place of the vacuum types. Our Petcock fits to right or left and each comes with the tap to tank O-Ring seal and assorted outlet fittings (petcock has 2 outlet ports). Fittings included: 2 ninety degree, 1 Straight fitting & 1 outlet port Plug. There is an "ON", "OFF" and "Reserve" position.

Tap to Tank Mount Screws (2) and Sealing Washers (2). Fits: All 650's 1970-84