Cylinder Head Sealing Washer Steel Head washers with internal seal. Used under 4 outer cylinder head crown nuts. Note: Not included in gasket sets. Made In Japan. Sold each. OEM Ref.# 90210-10004

Brass Cylinder Head Washer Can be used as a substitute for stock cylinder head sealing washers (#01-0650). Used on four outer cylinder head studs. 22mm. OD x 10.5mm. ID x 4mm. thick Note: All Cylinder head fasteners should be re torqued on newly assembled engines after they have been run at full normal operating temperature.

Top End Copper Sealing Washer Kit - 9 pc. Kit Contains: 1pc. # 90430-14043 ( @ Oil feed tube base at crankcase), 4 pc. # 90430-10027 ( @ Oil feed tube - Top of head at bolts), 2 pc. # 90430-11033 (@ Rear of cam chain guide support nuts to cylinder front), 2 pc. # 90430-06014 @ (Cam chain guide fastening bolts at front of cylinder). Fits: All 650's

Bottom End Copper Sealing Washer Kit - 13 pc. Kit Contains: 6pc.of # 90430-08143-00 ( @ Crankcase Bottom - Nut washers), 2 pc.of #90430-06014 ( @ Oil filter cover screws in clutch case), 3 pc. 90430-06014 ( @ 3 Clutch case upper front screws), 1 pc. of # 90430-06014 ( @ Tach drive retaining bolt), 1pc. 37R-82543-00/90430-11034 ( @ Neutral switch base). Fits: All 650's

Lower Engine Case Screw Set. - 18pc. Fits: Lower right hand & left hand engine cases on all 650's.

Engine Top Fastener Set - 55pc. 55pc. Kit Contains: 3 Hole Tappet Cover chromed Crown Nuts (12pc.) with matching chrome Washers (12pc.) + Cylinder Head chrome Crown Nut (8pc.) + chrome rocker shaft End Plug (4pc.) + Point/Cam Cover chrome Screws (4pc.) + Exhaust Stud chrome Crown Nuts (4pc.) with matching Stainless Lock Washers (4pc.) + 2pc. Chrome Oil tube banjo bolts, + 2pc. Chromed Cylinder front/Cam chain guide bar Nuts, + 2pc. chromed cam chain guide bar bolts. Fits: 1970-71 650's

Cylinder Head Hardware Set Fits: 1972-84 XS/TX 650's

Polished Chrome Shock Crown Nut - Short Type. 17mm hex x 10mm 1.25pitch x 16mm Long. Fits: All Footrest mount bars 70-84 + Fender mount thru point on 76-78's.

Chrome Thick Washer - 10mm x 27mm x 4.5mm. Fits: All Footrest mount bars on 1970-84 650's and shock absorber top mount stud on 1974-79 650's.

Advance/Breaker Housing Screw & Washer Set (6pc. Set). Includes: 3 countersunk flat-head type screws and 3 matching starlock washers. 2 sets required to do both engine housings on each engine. Fits: All 650's 1970-84

Bolt - Special Bolt that Holds the Tach Drive into the Clutch (RH Engine) Case. Fits: All 650's 1970-84

Tall Chrome Crown Nut Set (6pc. Used on Bottom of Crankcase). 8mm x 1.25 thread x 19mm tall (use 12mm wrench). Replaces OEM# 90176-08019.

Polished Chrome Crown Nuts (pk./10) - 8mm. x M1.25 thread.

Polished Chrome Crown Nuts (pk./10) Short type - 10mm. x M1.25 thread x 16mm. high (17mm. hex)

Engine Crankcase Bolts (Set/4). Bolts fasten engine cases together and pass thru cases from the top of the rear portion of the engine. We have replicated the early type attractive Chrome plated Domed head type Bolts and have the 3 sizes in a set of 4. Fits: All 650's 1970-84